How To Cut A Taper On A Table Saw

If you have been making furniture for an extended period, then there is a good chance that you need to make taper cuts at one point.

To cut a taper on a table saw requires a specific procedure and materials. So, the materials that you need are a powerful blade and a table saw jig.

How To Cut A Taper On A Table Saw

The first step is to install the blade protector. For this, you need to set the blade protector that you got along with the table saw.

Step 1

Change the height of your blade in such a position that even when the wood edge is seen to be obstructing, you are only cutting the base of your saw blade.

The standard components that come with a table saw are a blade guard system consisting of a pawl and splitter to prevent any kickback. If this system isn’t attached to your table saw, you have to get it set up on the table saw, and it has to be in proper working condition.

This guard system has a rubber shield that will hold the knife far away from your hand and deflect any flying pieces. Furthermore, the splitter will stop the deck from hampering the blade.

On the other hand, a kickback pawl is a defensive unit that contains small teeth that can catch your board and stop it from harming you if the knife connects or pinches during the cut. Moreover, it decreases the chances of a kickback risk.

Step 2

This step involves using the push stick. Now close your finger along the back of your board and hang on to the fence with the finger to tear up six boards broader and broader.

You need to concentrate on locking your board edge with an excellent fence that you got, to move it into the knife steadily and slowly. Now move your board over and then kick back the pawl entirely.

Switch off the table saw so that the cutoff or ripped part can handle the saw. Make sure to move aside in case it jumps back out of your saw. Furthermore, make some push stick not out of lumber but plywood because the former might fall apart and break as you drive.

The only safe method to properly secure a thin piece of board past your spinning blade is by always moving the boots and sticks. So, make sure that you have a shoe or a stick nearby whenever you use the table saw.

Step 3

Using a straightedge and a pencil, draw the tapered cut on your plain while including the kerf. The kerf is a line made to identify the two sides of the opening your blade will make.

In this illustration, the finished part will be on the left, and the materials disposed of your cut will be on the right.

Step 4

Now you need to attach your guide board to the blank. To make a guide board, use a board or a pressed wood piece wide enough so that it can cover the waste and be adequately long to reach a few inches past the blank’s two ends.

Adjust your guide board using your kerf line and then tie it to the waste with a few clips from some screws or the air nail.

Step 5

Turn the board from one end to another. You need to set your table saw fence in the correct position with your guide board.

Step 6

In the last step, pull back your guide board, switch on the saw, and slice the part. The finished piece will drop off on the table. All the waste is recyclable except for the two pinholes.

How To Cut Tapered Legs On Table Saw?

If you need to make a tapered cut on a board, you could take it over to the sawhorses and try to freehand it with your circular saw, but there is a better way to cut tapered legs.

You can try making complicated jigs to make tapered legs on a table saw. On the other hand, you can create a simple jig that you can take with you to any job site. Here is how it works.

  • Take a piece of plywood. It doesn’t matter if it is a 1/6 or a 2/6. The main factor here is that you need to ensure it has one nice straight edge.
  • Raise the blade about a 16th of an inch above the surface of the table. This is to make a very shallow kerf. The next thing you need to do is turn the saw on and make the cut.
  • Set the fence at about 5-inches. Let the kerf be at about five inches. Now, line up the tapered cut with the cut line of the jig and secure it from the backside with a couple of screws. 

Now, cut it without removing the fence, and you will have your tapered cut.

Leave a Comment